EDIT: dbzer0 had nothing to do with this ban, it was done by a Lemmy.World admin.

I updated my post after another user stated that it wasn’t lemmy.world admins that performed the ban but the db0 team that did. I can’t say with certainty that’s actually the case since the modlog is pretty opaque and I don’t have full knowledge of how [federated] actions are propagated & displayed.

I (incorrectly?) assumed since those communities had existed for so long on the dbzer0 instance they had at least tacit approval from the admins there and were in communication with them enough that a full ban wouldn’t occur – when I saw the removal in the modlog I didn’t even consider that possibility.

Sorry for kicking up drama here if the Lemmy.World team had no part in this :(

You can also use electrical tape to cover the 5V pin: https://community.octoprint.org/t/put-tape-on-the-5v-pin-why-and-how/13574

What kind of filament is that printed with and are you concerned about it failing over time? Especially if there’s spinning disks in there I’d be paranoid as hell about it falling.

the only way to download it is with a premium subscription

This doesn’t help you on a mobile device, but in case others weren’t aware of its existence, there’s a great open source tool for downloading from many/most websites: yt-dlp

Seems more economic than political to me, but also why such the strong reaction to an on-topic reply? As you even said yourself:

I don’t really care all that much about any particular issue. I enjoy copying the ideas suggested by others in the fediverse and transforming them into new issues, as many individuals do not take this initiative.

Your account has existed for all of 3 hours and you’re trying to come off like a well-known fixture of the community whose opinions are above reproach. I’ll also say it seems suspect how quickly detracting comments are earning downvotes but not replies in this post.

In short, I don’t believe you, your post or its engagement, are sincere.

Imagine a social media landscape where every piece of content is perfectly tagged

working tirelessly to make your online experience safer and more enjoyable

All of this feels a little disingenuous when it’s not even mentioned that all this tagging and classifying would also make it much easier for training LLMs or tracking groups/individuals/movements.

It’s not web based but MKVToolNix GUI is pretty user friendly. I haven’t dug into it too deeply so I don’t know if it offers any automation tools to batch change files etc.

FAN OF ALL CAPS TITLES AND VOTE BEGGING I AM NOT

I whipped up a basic page with PHP and just used XAMPP when I was on Windows. I recently switched my daily driver pc to linux and haven’t updated it yet. I only used it to save MP3s, videos at yt-dlp default “best available” settings, and a custom option that lists available video/audio formats where I can specify the ID to grab of each. No validation or sanity checking etc, just some switch statements and basic form functions.

main page

custom selection

Awesome, glad to hear it!

When you’re ready to try printing again I agree with the suggestions to:

• lower the bed temp to ~60c
• avoid using glue sticks or similar since it shouldn’t be necessary with PLA, and will just add another variable
• keep working through first layer print tests

I’m surprised you’re having adhesion problems with a PEI build plate. When I swapped to PEI it was like magic; filament effortlessly sticks and finished prints pop off from a gentle flex. There isn’t like a plastic shipping cover on it or something is there?

Anyway, good luck with the rest of your troubleshooting – I’m sure you’ll eventually get it dialed in :)

I have no personal experience with a failed firmware update but a quick search returned https://forum.sovol3d.com/t/sv06-bad-flash-probably-needs-bootloader/1452 and “solved” = https://forum.sovol3d.com/t/sv06-mainboard-brick-after-updating-sovol-firmware/862/52

Seems like for some people it was ultimately the sd card being faulty that was causing the failure, especially if it was the sd card included with the printer.

Good luck!

To my eyes the inner rectangle portions look pretty good and uniform. If that’s a brim around the outer edge it’s definitely not doing its job.

Is the severe warping and sharp creases from you fighting to remove it from the plate or is this basically how it looked on the printer?

EDIT: If there’s any kind of draft near the printer maybe you could try using a cardboard box or something to build a makeshift enclosure.

Are you saying the surface in the picture is the one that touches the bed? If that’s the case it should be nearly perfectly flat and smooth(ish depending on bed texture). If that’s the orientation it prints in there’s still an issue of distance and possibly belt tension or something else because of those waves and deep grooves. There’s a bunch of different methods to level a bed but ultimately you want the nozzle to slightly squish the filament it is putting down, in the picture it looks like it might not be.

As for the bed being clean, if you haven’t yet I’d definitely spray some isopropyl alcohol and wipe it off, taking care not to touch the bed with your hands at all – oil from your skin will easily cause adhesion issues.

Larger prints in general, and especially if there’s temperature variance while printing (drafts), can start to pull off the bed as the material contracts. You may need to add a brim in your slicer to help keep it welded down. When it’s necessary to use one will be a learning experience as you get used to your particular printer and environment.

This could have been a fun mashup but this execution just feels kinda wrong/gross overall to me.

• Why are so many main characters not included (Hermes, Zoidberg, Nibbler etc.)? At least Bender is present as the flaming mass we all fondly remember from the film…
• Was it really necessary to include perky nipples and a camel-toe on Amy?
• The staff Professor Rhod is holding has what resembles a golden swastika in the only significant change from how it appears in the movie. And though the Professor is occasionally shown without teeth in the show is there a reason he doesn’t have any here?
• Why does that train have eyes?
• Just a bizarre composition in general. Why include so much of the stone and vents around Amy, then make the openings between the slats just reveal the background image? If Leela was shifted over slightly left her fading tendrils and feet could have been cleanly hidden behind the Professor.

Seems like a huge waste of filament and print time. I use Rubbermaid TakeAlongs which are air-tight and transparent, negating the need to label what’s inside.

Have you looked into Pseudotv / PseudoTV_Live?