Looks like maybe ~2mm spacing on these lines so possibly just belt related.
Check if it’s worse in a specific axis, the belt might might just be too tight.

Or offcenter, or something… looks like teeth from a belt, idler or pulley

The incest trope is everywhere

Yea, I was referring to the OSI model.

I can’t know for sure if they kicked the bucket or not, but they aren’t around here anymore.

They seemed like a genuinely cool person and it makes me sad that they might be gone.

They’ve mentioned accepting and not fearing death, but also wanting to remain anonymous.
I won’t doxx them, alive or not, but know that it seems someone has since been taking care of what they considered to be their life’s work (their words).

May they remind y’all to cherish whatever time you do have.

Whatever you do, make sure you have working backups first.

I imagine you could copy the docker volumes over, but that’s more work than of they’re “mounts”, in which case you can just copy the corresponding on the host. Use scp or rclone or whatever to copy the files over

So much baiting, the chat bot never had a chance.

A single misconfigured thing can suck real bad as you’ve seen.
Selfhosting involves lots of things that can be misconfigured or go bad.

That’s not to scare you out of it out anything, merely to congratulate you in seeking knowledge first.

Disclaimer: I’m biased towards networks because I’m a network engineer, opinions may differ.

I would say… having at least a vague grasp of layers 1-4 of the traditional network model is a decent start.
You don’t need to understand everything, but knowing a minimum will help a lot imho.

It’s hard to point you in the right direction without knowing what you already know or not.

Aside from adhesion itself, maybe that specific filament is (also) underextruding?
I have has a batch of 1.75mm filament that was actually something like 1.6ish. I tried to have it stick, but nothing worked because it simply wasn’t extruding enough.
I eventually measured it with calipers, set that in the slicer and then it started worked fine.
Similarly, maybe your .2mm nozzle has a partial clog?

Sadly, the CAD software I have the most experience with is SolidWorks. It has its quirks, but I like it and I know my way around.
Which is too bad, because it’s completely absolutely fucking stupidly expensive for any home use.

Not to mention I’ve heard stories of people getting caugth through exported models’ metadata and getting sued for publishing models made with pirated or student versions or whatnot.
I’m not even a business and whilr I have no moral qualms pirating software, I don’t exactly wanna deal with an actively hostile company either.

I’ve switched to onshape for now, but I know enshittification will eventually butcher it too.
There’s a few others I’ve tried that I either can’t get good at, or that simply lack functionality.

I’ve been meaning to try Alibre CAD, but last I checked, their trial thing required back and forth with a rep and I just never bothered.

I don’t even mind paying, yet not $5k yearly or some shit.
If you ever find something, ping me.

Yes and these comments also show up on mastodon.

I’ve not had good luck finding something that gives me the confidence to go about it

Now’s a good time to make sure you have good backups.
Knowing you can fallback to your backups helps a lot with confidence.

One this that’s really hard to replace is DDoS protection.

I leave my phone further away.
Close enough that I’ll hear it if there’s an actual emergency, but far enough that I won’t reach for it just because I’m bored.

That’s enough to take care of most of my mindless night scrolling.

If I just can’t fall asleep, sometimes I’ll go drift off in the hammock outside or something that’ll cool my body a bit.
Tbh, sometimes I just rub one out ¯\_(ツ)_/¯
Also works as a decongestant.
I’m not a doctor, don’t use this as medical advice.

If it starts fine, but performance drops off a cliff after a while, it might be a heat issue.
I ended up putting such a flaky drive in a bag and wrapping a flexible icepack around it.
Not a great solution, but kinda good enough to get some data off of it.

I use this one:
https://play.google.com/store/apps/details?id=de.orrs.deliveries

It can usually get the status of most courriers unless they’re actively hostile against API/scraping.
Worst case you can still track status manually, or open the webpage.
It doesn’t track payment, but I don’t usually have a tracking number before paying.
I think you could technically add your own custom status entry.
I keep them as active until shipped and verified after which I mark them as completed.

Works well enough for my needs.

Just got my 9 year sticker in the mail too.
I don’t even use it as much these days, but it helped me a lot when I was starting out, and I still use it for the webcam.

I donate monthly to Wikipedia, Signal, and Octoprint.
Probably cheaper than Netflix too nowadays.

It’s not necessarily heavy songs to begin with, but the soundtrack for Bridgerton has a few instrumental covers with string instruments that are an interesting take.
One of the groups that does these covers is Vitamin String Quartet and off the top of my head I remember a few of the songs they’ve done like Zombie, Yellow, Wrecking Ball, Thunderstruck, Smooth Criminal and whatnot.

Might be something that interests you.

You can use an adapter just fine.
Or use a 5.5" drive caddy, that’s just a little drawer that slides in and out.
Real question is it you have enough SATA connectors available.

A normal 1-gang electrical switch (without a LED) would work without this concern.