I love Elegoo’s printers. Got a Neptune 2S and a 3 Pro tuned and running Klipper, they’re good workhorses
I love Elegoo’s printers. Got a Neptune 2S and a 3 Pro tuned and running Klipper, they’re good workhorses
Looks like nice even pressure, good job! It looks like you’re underextruding a bit though
It may try to connect to open wifi networks instead, maybe
It’d be cheaper, sure. But that assumes anyone actually wants to run things locally. My VP is an elderly woman who would love to get off the Board as well. We just don’t have volunteers to run things. I joined up so our HOA didn’t get handed to a lawyer to run, which would cost even more.
Prior to having a management company, the HOA treasurer embezzled about $40,000. It’s the reason they got the management company in the first place.
Getting out of it is the hardest part for us right now.
We’re in a small 28 unit condominium, so our dues go towards insurance for all buildings (only exterior, have to have our own for studs in), water, lawn service, management company, etc. Our dues are almost $400/month.
Yes, per month. It absolutely blows, especially when we’re trying to sell our unit and it’s been on the market for almost half a year.
I’m the HOA president so I know what all our expenses are (and have fought to keep increases to a minimum, including negotiating the community water bill with the water company), and unless we kick out the management company (Not going to happen) the dues are just going to stay high. We’re preparing to refuse an increase for the next year.
My guess is that it may not be factoring traffic conditions for bicycle directions
“I don’t care that it’s in the shape of a whale!” is now my new favorite phrase and I now plan on 3D printing that to hang on my wall
I always read it as Law Enforcement Officer
With Sunlu’s new filament joiner coming out, I might give this a try by splicing segments of different browns together into a big roll. It’s a very near concept, and your print looks amazing!
Ketchup + Mayo is called Fry Sauce here in the USA (This can vary based on the state)! Will definitely try with some diced onion next time I make some
The following was added to my fstab
//192.168.86.181/TrixieTV /home/brobot/Storage/Completed/TV cifs credentials=/home/brobot/.smb 0 0 //192.168.86.181/TrixieMovies /home/brobot/Storage/Completed/Movies cifs credentials=/home/brobot/.smb 0 0
The credentials are using a new user ‘moose’ that owns the folders and has full control
user=moose password=3141
I’ll look into that, thanks!
We just had a total power outage, and restarting my main machine I remembered I have Linux Mint installed as duel boot. I’ve been waiting for a final push to get me to migrate away from Windows. Would it be easier to do all this from Linux Mint instead of Windows?
No GUI on my end (It’s been fun learning to use a headless server). I have to sudo to be able to do anything in the mount locations. Using ls -s, the permissions and owner aren’t changing after using chown and chmod.
Yup, the mount is authenticated and the Share Permissions on Windows have it set to Full Control for Everyone, plus ‘Password protected sharing’ is turned off under Advanced Network Settings.
For calibrating your printer, I always recommend https://teachingtechyt.github.io/calibration.html. Everything is step-by-step and helps teach you about the calibrations and what different settings do. I agree with the other commenter that you’re underextruding, based on your layers not filling in. Getting your E-steps calibrated is extremely important, then I’d start working on flow rates (which can change between rolls and brands)
That’d be your carrier being bad, not the Pixel. You could be right next to the tower, but depending on congestion and your plan you could be limited. You’re driving a car that can go fast, but getting stuck in traffic.
I noticed that as well. Makes sense since I just got the update as well.
Device information
Sync version: v24.03.26-14:56
Sync flavor: googlePlay
Ultra user: true
View type: Cards
Push enabled: false
Device: cheetah
Model: Google Pixel 7 Pro
Android: 14
I’d give Teaching Tech’s calibrations a try. His website has a great guide for tuning every part of your printer. Teaching Tech 3D Printer Calibration
You said you recently got a gigabit plan, but that’s related to your home download speed. Check to see what your upload speed actually is. Depending on your ISP’s plans, you might have a speedy download but a slow upload.
I found it quite fun. Very meta, more of a fun nod to the community