Spotify and other such services almost certainly sound worse because they are compressed. But it’s not really a like for like comparison with vinyl. Spotify is streaming audio for people who want to play music casually in cars, earbuds etc. It offers convenience, not perfect sound fidelity. FLAC / CD on the other hand could be compared to vinyl and would win hands down for better frequency and range. The only reason they wouldn’t is if the CD master sucked and the vinyl master didn’t.

And vinyl is very lossy in its own way. The (digital) master of each side undergoes dynamic range & frequency compression to fit the limitations of the format (e.g. to reduce sibilance, track width). Then the master is cut into a lacquer disc from which a “father” is made, from which “mothers” are made, from which stampers are made and from which the vinyl record is made. So the vinyl in someone’s hand is a copy, of a copy, of a copy, of an altered digital master. The stamper too wears out so if someone is unlucky they get a pressing right the end of its life. And playing the disk can cause wow, flutter, distortion and general wear & tear can cause hiss, pop, dullness and scratches.

So vinyl will never sound better unless it received a better master than other formats.

In the 70s and 80s there were kids toys which played injection moulded plastic discs with a stylus that tracked the groove. I think you might be able to achieve something similar out of a printed record if it was spun fast enough but it wouldn’t sound great.

I had the misfortune to have some PLA snap just before and after the direct drive in my Bambu P1S and it took ages to get it out. I think age and moisture can affect filament, especially it blended with wood dust, sparkles or something which undermines it even further. I’ve resorted to packing my AMS with silica beads to hopefully mitigate for the issue and I threw out the filament that caused the issue. Ironically this is one of the few places a bowden extruder is any benefit - if the filament snaps just push it from behind through a heated nozzle until the blockage clears.

Been reading there’s too many complications (different state for one, more red tape) for the value. They’re going for the low-hanging fruit right off, liquid money like bank accounts, working their way up from there.

I think it would make sense to seize & sell assets in New York but I bet there are some really complicated ownership deals on his properties and some will be laden with lease agreements, debt, mortgages etc. They might see Mar-a-lago as having a clean ownership making it worth the effort of going after.

Scotland absolutely fucking hates Trump so I think they would be very happy to overcome the legal friction with the sale of his Scottish courses if it came to that.

But I think most likely she’ll target US properties & assets first for obvious reasons, in her own state first but anywhere is fair game - a judgement in state of New York is enforceable anywhere even if there are requirements and legal effort to “domesticate” it to target state to enforce it. I will be very amused if Mar a Lago is seized though knowing Trump he’ll try to pretend the thing is his “homestead” despite it having non-residential status and he himself only living there through a loophole.

Hopefully it happens before Trump can cash in on his Truth Social deal

I wonder what would happen if Putin straight up offered to cover his debts? I expect Trump would actually accept that offer and his idiot base would see nothing wrong with it if he did.

There is, you just have to find it while the car sinks or the flames spread. It’s not the normal button that a user might be accustomed to pushing to get out so they might not know where it is and finding it in time might be the difference between life and death. For front doors it’s usually a lever somewhere but in some model Ys and the cybertruck the rear door release is hidden. under a mat in the door recess.

When your Tesla is on fire, or sinking, you can play a fun little game called “Find the manual door release”

I’m sure some people are having the same sentiments about Donald Trump right now.

I wonder if there shouldn’t be a way of federating duplicate groups after the fact so one doesn’t have to “win”, they just all combine as one.

Forgiving is the word for this - being able to undo mistakes and recover. I reckon FreeCAD would massively benefit from doing a complete feature freeze and focusing on usability for a couple of releases.

I think FreeCAD would win a lot more converts if it focused on usability. Fusion360 and Onshape are parametric modelers just like FreeCAD yet they’re way simpler, taskcentric and more forgiving tools to use.

Did you turn layer ironing / smoothing on for the last layer not all top layers? Aside from smoothing modern slicers can also use more attractive patterns for top layers than zig zag such as hilbert.

It also looks like you might have underflow issues so maybe check your e-step setting on your printer to ensure you’re extruding proper amount of filament. There are articles that explain the process but you basically mark a reference point on the filament, e.g. 10cm away from where it enters the extruder, tell the printer to extrude 10cm, mark and measure how far away the mark is from where it’s meant to be. So if the filament moves 7cm when it should have 10cm then your e-steps need to be multiplied by 10/7.

Wouldn’t the problem be that you’d still have to remove the print, wash it, empty the vat, clean the vat & build plate and only then could you put the print back in and then fire up the UV. Meanwhile you won’t be using the printer for anything else. Maybe it’s easier to just buy something that can wash & cure separate to the printer or leave the print out in the sun to cure.

Plastic cutlery is disappearing in most countries - it’s all wood or cardboard now. I suppose someone could make a business of collecting used cutlery where it’s still in use and recycle it (not necessarily into filament), but I wonder if it would be economically viable.

BL touch works great but you need to get the Z offset. Then you can just G29 before the print or whenever and it works great. I hate manual levelling and these days there isn’t much reason for it. I’ve just upgraded to a Bambu P1S and levelling is even more straightforward since there is no Z-offset since it uses the hotend itself to probe.

In my Ender 3 Pro I found tightening the screws too much made the bed bow, so I loosened them until they were just firm but not forcing up the corners. I also replaced the default springs with stiffer ones so once set they stayed set. I also built a custom Marlin firmware and I changed the bed mesh algorithm to probe more points and use a more sophisticated algorithm to compensate for levelling. This was with a Bigtree 1.2 board which barely had enough memory for the firmware but I made it work. After that I really didn’t have any issues. Biggest pain was dialing in the Z-offset on the BL touch.

I’m sure it’s easier for them in a sense. I write software to control cloud based devices that are not adjacent to the caller and they use message based comms. But it’s also an unnecessary overhead to upload a 70Mb file to the cloud and back down again. If I were writing this software I’d consider some shortcut mechanism where the send file action could be sent to the printer directly and only fallback to cloud if that was not possible. If for no other reason that saving myself money and general responsiveness. I’m sure it would be achievable by doing a UPnP scan of the local network and allowing the PC to talk to the printer if it possesses and sends an API key - much like Octoprint works. Also, local network probably helps for the camera which could just blast a feed out on UDP.

I’m not sure it helps them “steal” models because they probably have 100,000s of models passing through their system every day. It would be a wall of noise and random junk. And these aren’t models in the CAD sense, but some STL meshes and print settings. It does give Bambu information about what filaments people are using and in what quantity, the frequency they print as well as geographic location. That might be useful for marketing. If a government was interested in a particular user, they could also see in retrospect what they were printing. e.g. if someone were printing gun parts then maybe there would be evidence of that in the cloud.

I have a P1S and I don’t really follow why it is necessary at all to send prints off to the cloud. Yes, it could be useful if printer and PC / app are on separate networks. But if they’re on the same network then they should directly communicate.